男男互攻互受H啪肉NP文,国产乱妇乱子在线播放视频,国产亚洲AV片在线观看18女人,国产精品视频久久久

                    目   錄

                   Directory

中文版說明書Chinese version of the manual

概述Outline ………………………………………………………………………3

特點Feature………………………………………………………………………3

技術指標Technical Specifications……………………………………………3

安裝及操作說明Installation and operating instructions………………………3

維修Service………………………………………………………………………3

包裝及搬運說明Packaging and handling instructions………………………4

印花設備及熱轉印設備保修單Printing equipment and heat transfer equipment warranty single……………………………………………………4

英文版說明書English manual…………………………………………………5

機器零部件標示圖Machine parts labeled diagram……………………………………7

電路接線圖Circuit wiring diagram……………………………………………………8

概述

本機（JC-7A/17氣動上下熱雙工位壓褶機）可將衣物按要求通過高溫及壓力的配合壓出各種壓褶定位效果，操作速度快，省時，省力，是現代制衣壓褶工藝中的首選機器。

特點

●         電子數顯恒溫控制溫度，準確性高（±2℃）；

●         發熱采用進口鋁合金澆鑄導熱原理，省電，溫度均勻，溫差系數�。�

●         電子時間控制，工序完成訊號指示；壓力隨意調節；

●         機器采用工作發熱板左右直線移動，方便燙印，不會移位。

技術指標

電壓（V）：220/110

功率（KW）：6.6  7.5  9.0  10.0   19.5

溫度范圍(℃)：0-399

時控范圍(S)：0-999

工作臺尺寸(㎝)： 40×40  40×50  40×60   50×70  60×80 

包裝尺寸(㎝)：135×78×72  135×78×72 150×78×72  98×80×152（附軌道）

              98×86×152（附軌道）

安裝及操作說明

①    本機要放置在平穩的地面上，機器四周應有一米以上空間，以方便安裝及維修。

②    確定機器安裝位置后，安裝固定好所配腳架，固定好腳架，把機器放有腳架上，放穩機器后，確定機機安裝位置后，配備單相220V電壓或110V電壓交流電源，電壓波動范圍-10%-5%的閘刀開關或空氣開關（注意：電壓波動范圍-10%-5%時請配備合適的穩壓器），以便控制電源通斷，并必須接可靠地線。安裝完畢后，再認真檢查一次，以免誤接。(注意:整機必須有合適牢靠的保護地線)

③    連接所配壓縮機氣接頭，打開氣壓，將壓力表調制(4pB-6pB)使發熱板升起，壓力最大可調至8 pB；

④    插上電源，打開電源總開關，電源指示燈隨即著亮;

⑤    將溫度表調較至所需溫度(通常為120℃-200℃)；

⑥    將時間表調較至所需時間(通常為10至30秒左右)；

⑦    機器準備進入工作狀態時請先準備好被壓褶定形的相關物品放在易操作機器的附近。

⑧    操作機器時，機器上設有兩個工作臺（指工作發熱板1與發熱板2，以下簡稱工作臺），一個下壓工作板（發熱板3，以下簡稱下壓工作板），可通過工作臺左右水平移動操作完成承印任務。機器上設有自動及手動功能，當用手動功能時，將第一個工作臺移動到下壓工作板下面，工作臺到達指定位置后，按一下手動按鈕，下壓工作板隨即下壓，壓褶定形指定時間到后，工作下壓板上升，接著可移動第二個工作臺，重復上動作可完成第二個工作臺上的壓褶定形任務；當用自動功能時，將第一個工作臺移動到下壓工作板下面，工作臺到達指定位置后，工作下壓板隨即下壓，壓褶定形指定時間到后，下壓工作板上升，接著可移動第二個工作臺，重復上動作可完成第二個工作臺上的壓褶定形任務。

⑨    該機型為專用于壓褶定形機器，不需要配備其它物品，如硅膠等。

維修

1．            壓力：下壓發熱板不平時，可調較發熱板中心的四條絲桿；如壓力不夠時，可調較機器的過濾器，把過濾器上高突起的左邊蓋子拔起，順時針是增加壓力，逆時針是減少壓力，注意：壓力最大可調至8PB。

2．            時間：當壓褶定形時間到達而發熱板未升起，則須檢查電磁閥觸點是否燒壞或時間表是否燒壞。

3．            溫度：當所調溫度到達時，溫度表會顯示已到所需溫度，如不升溫，則檢查①接觸器是否壞了；②溫度表是否失靈；③發熱管是否燒壞；④高溫線是否脫落。

4．            下壓工作板不下壓：①檢查工作臺是否到位；②氣壓是否在4pB以上；③感應開關是否與磁鐵感應；④時間表是否計時，會計時，則說明感應開關沒問題則需檢查電磁閥；⑤電磁閥是否有電，有電而不動作，則是電磁閥壞。

注：氣壓力應調到(4pB-6pB)，如發熱板未升起，請栓查氣壓線路，電磁閥是否暢通，過濾器是否打開。

包裝及搬運說明

①    40×60規格以下（含40×60規格）當客戶指定用木箱包裝時：用可承重100公斤以上叉車搬動；不用木箱包裝時，可兩到三個兩手抓緊機器前后手把位置平穩抬動機器，輕輕放下即可。40×60規格以上，當客戶指定用木箱包裝時，因本機主機下方裝有活動腳輪及腳杯，用木箱包裝時，為安全及防止機器跑位，請一定切記把四個腳杯全部調至接觸到木箱底盤表面固定不能隨意移動后方可包裝，用可承重150公斤以上叉車搬動。

②    40×60規格以下（含40×60規格）當客戶指定用木箱包裝時：用可承重100公斤以上叉車搬動；不用木箱包裝時，可兩到三個兩手抓緊機器前后手把位置平穩抬動機器，輕輕放下即可。

      印花設備及熱轉印設備保修單

產品型號： □JC-7A/17上下熱壓褶定形機       出廠編號：                   

保修條例

1．            在保修期內憑此單和送貨單（或收款收據）修理；

2．            保修期限：從出售起為一年。

3．            保修注意事項：

◆  凡未經拆動，確屬產品制造不良的故障或損壞，均由我廠負責修理或更換損壞的零配件；對使用不當?shù)热藶橹圃斓墓收匣驌p壞，不屬保修范圍；

◆  非電器配件不在保修范圍；

◆  用戶與我廠聯系解決質量問題時，請寫明機器型號，出廠編號，故障現象。

Outline

The machine (JC-7A/17 pneumatic crimp top and bottom heat duplex unit) can be clothing as required by high temperature and pressure with pressure crimp positioning of a variety of effects, operating speed, saving time, effort, is the modern system clothing pleating process of choice for machines.

Feature

Electronic digital thermostat control temperature, high accuracy (± 2 ℃);

Fever imported aluminum alloy casting thermal principle, power, temperature uniformity, temperature coefficient is small;

Electronic time control, process completion signal indication; pressure adjustable;

Machine uses linear movement working around hot plate for easy stamping, will not shift.

Technical Specifications

Voltage (V): 220/110

Power (KW): 6.6 7.5 9.0 10.0 19.5

Temperature range (℃) :0-399

When the control range (S) :0-999

Table Size (cm): 40 × 40 40 × 50 40 × 60 50 × 70 60 × 80

Packing Size (cm): 135 × 78 × 72 135 × 78 × 72 150 × 78 × 72 98 × 80 × 152 (with Rails)

              98 × 86 × 152 (with Rails)

Installation and Operation Instructions

The confidential placed on a stable ground, around the machine should be more than a meter space to facilitate the installation and maintenance.

Determine the machine installation location, the installation fixed dispensed tripod, fixed tripod, tripod placed on the machine, put the stability of the machine, confirm their installation location, with a single-phase voltage 220V or 110V AC power supply voltage, voltage fluctuation range -10% -5% of the knife switch or air switch (Note: The voltage fluctuation range -10% -5% when equipped with a suitable regulator) to control power on and off, and must be connected to a reliable ground . After installation, carefully check once again, in order to avoid incorrect connections. (Note: The machine must have the proper protection of solid ground)

Connection with a compressor gas fittings, open pressure, the pressure gauge modulation (4pB-6pB) the heating plate rises, the pressure is increased to a maximum 8 pB;

Plug in the power, turn on the power switch, power indicator light then forward;

The thermometer adjusted to the desired temperature (typically 120 ℃ -200 ℃);

Will be adjusted to the desired schedule time (usually 10-30 seconds or so);

When the machine is ready to enter the working state ready to be pressed pleats please amorphous related items placed near the machine easy to operate.

Operating the machine, the machine is provided with two tables (refers to the work with a heating plate heating plate 2, hereinafter referred to as bench), a work under the pressure plate (hot plate 3, hereinafter referred to as the work under the pressure plate), through the work Taiwan about the level of move operation is complete printing task. Machines equipped with automatic and manual functions, when using the manual function, the first table is moved to work under the pressure plate below the table arrived at the designated location, click the manual button, under the pressure of job boards immediately under pressure, pressure after the specified time to tuck amorphous, working up under the plate, followed by a second movable table, repeat the action to be completed by the second crimp workbench amorphous task; when the automatic function, the first table move to work under the pressure plate below the table to reach the designated position, working under the plate immediately under pressure, crimp setting specifies the time to post, under the pressure of rising job board, can then move the second table, repeat the action to be completed the second work bench crimp setting tasks.

The model is designed to crimp setting machines with no other items, such as silica gel.

Service

Pressure: heat plate is not usually under the pressure, adjustable heating plate center four screw; such as pressure is not enough, adjustable machine filters, the filters on the left side of the lid uprooted high protrusion clockwise to increase pressure and counterclockwise to reduce pressure, attention: the greatest pressure adjustable up to 8PB.

Time: When crimp positioning time is reached while the heating plate is not raised, it shall check whether the solenoid valve contacts burned or timetable is burned.

Temperature: When the temperature reaches tune when the thermometer will display to the desired temperature, if not heat up, check whether the contactor ① bad; ② thermometer is malfunctioning; ③ heat pipe is burned; ④ temperature line is off.

No less than the pressure plate under the pressure of work: ① Check the table is in place; ② whether 4pB above atmospheric pressure; ③ sensing switch and magnet induction; ④ whether the timing schedule, accounting, then the description of sensor switch no problem need to check the solenoid valve; ⑤ solenoid valve if there is power, there is power without action, the solenoid valve is bad.

Note: The air pressure should be adjusted (4pB-6pB), such as the heating plate is not raised, please check the air pressure line bolt, solenoid valve is open, the filter is turned on.

Packaging and handling instructions

40 × 60 size less (including 40 × 60 size) When the customer specifies use wooden packaging: can load 100 kg with a forklift to move; without wooden packaging, you can grasp with both hands two to three locations around the machine steady hand lift the machine gently down to. 40 × 60 specifications above, when the client specifies packed in wooden cases, because of the local host is equipped with casters and feet below the cup, packed in cases when, for safety and to prevent the machine moves, be sure to remember the four foot cups All raised to come into contact with the surface of the fixed wooden chassis can move freely before packing can load more than 150 kilograms with a forklift to move.

40 × 60 size less (including 40 × 60 size) When the customer specifies use wooden packaging: can load 100 kg with a forklift to move; without wooden packaging, you can grasp with both hands two to three locations around the machine steady hand lift the machine gently down to.

 Printing equipment and heat transfer equipment warranty

Product Type: □ JC-7A/17 pressing down pleats positioning machine factory          number:

Warranty

1.During the warranty period virtue of a single and delivery note (or payment receipt) repair;

2.Warranty period: from the sale of up to one year.

3.Warranty Note:

◆Whatever is not dismantled, indeed poor manufacturing faults or damage, are responsible for the repair or replacement of our plant damaged parts; against improper use of artificially created failure or damage is not covered under warranty;

◆Non-electrical accessories not covered under warranty;

◆Users contact with my factory to solve quality problems, please specify the machine type, serial number, failure phenomenon.